Knowing Plumbing Basics is Essential When Installing a Bathtub

Book

Just about everyone maintains their own unique way of thinking about Tools You Need to Install a New Bathtub .


How to Install a Bathtub
Installing a bathtub isn't exactly rocket science, but it does call for strong plumbing, carpentry, as well as often, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably difficult job. If the old bathtub is easily obtainable, the job can relocate quickly; if you need to open up a wall to eliminate the old bathtub and also position the new tub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will certainly require an assistant to vacate the old bathtub and also embeded in the brand-new one. Make sure you have qualified yourself for the job and are comfortable attempting it. Instead of employing a specialist to take over a halfway-completed project, it is much better to consider utilizing one before you start. Opportunities are you might need a specialist plumber to make tube links.
This write-up will certainly aid you mount a brand-new bath tub in your washroom if you have actually already gotten a new tub and don't require to transform the plan of your previous water pipelines.
Your tools and material list need to consist of the following:
  • New Bathtub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipe Caps


  • Removing Old Touches


    If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you must do is disconnect the water. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The process of getting rid of the existing faucets can be quite troublesome as a result of the restricted gain access to that is frequently the situation.
    Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the taps. Have a towel all set for the continuing to be water that will come from the pipelines. As soon as the supply pipes have actually been eliminated, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from turning throughout this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned of any old securing compound.
    Prior to moving on to fit the brand-new faucets, compare the pipe links on the old taps to the new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the brand-new faucets to fit.

    Fitting New Taps


    If the tails of the brand-new taps are plastic, after that you will need a plastic connector to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end provides a connection to the current supply pipes.
    If you need to fit a monobloc, after that you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
    Next off, place the tap in the placing hole in the bath/basin making certain that the washers are in location in between the faucet as well as the sink. Protect the faucet in position with the maker offered backnut. When the tap is securely in position, the supply pipes can be connected to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal tap adapters. The previous kind needs to be attached to the faucet finishes initially, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.

    Mounting the Tub


    Utilizing the two wood boards under its feet, position the tub in the required placement. The wood boards are practical in uniformly spreading out the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four small factors.
    The next objective is to guarantee that the bathtub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the bathtub up until the level checks out degree.
    To install taps, fit the bottom of the outermost adaptable faucet connector to the suitable supply pipe by making a compression sign up with; after that do the same for the various other faucet.
    Turn on the water and also inspect all joints as well as new pipework for leakages and tighten them if necessary. Fill up the bathtub and likewise examine the overflow outlet as well as the typical outlet for leaks.
    Ultimately, fix the bath paneling as explained in the maker's instruction manual. Tiling and also securing around the tub should wait till the tub has been made use of at the very least once as this will certainly resolve it into its final placement.

    Planning for the Installment


    First of all, the supporting frame provided with the bathroom ought to be fitted (if called for) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets system to stop strain on the bath tub.
    Fit the flexible tap adapters to the bottom of both faucets making use of 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize every one of the supplied washers.
    Link the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its last setting.

    Tiling Around the Tub


    In the location where the bathroom meets the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to split a stiff seal, creating the water to permeate the wall in between the bath as well as the tiling, resulting in difficulties with dampness and also possible leaks to the ceiling listed below.
    You can pick from a selection of coloured sealers to assimilate your components and also fittings. They are marketed in tubes and cartridges, and also can sealing spaces as much as a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of soaked paper or soft rope. Bear in mind to always fill up the tub with water before sealing, to permit the movement experienced when the tub is in use. The sealant can break fairly very early if you do not think about this activity prior to securing.
    Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently readily available on the market. It is a good idea to fit the floor tiles utilizing water-resistant or water resistant adhesive as well as cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub Yourself

    We hope you liked our post about Installing A Bathtub. Thank you for spending some time to read our content. Liked our piece of writing? Please share it. Let another person discover it. I love reading our article about How to Install a Bathtub Yourself.


    Book 24/7

    Leave a Reply

    Your email address will not be published. Required fields are marked *